MPBGP OSPFV3

R1,R2,R3 corren OSPF ver 3
 Estan en el sistema sutonomo 65001

R4,R5 corren eigrp for ipv6
 Estan en el sistema autonomo 65002

############tabla de neighboors ####################
R2#
R2#SH BGp IPV6 UNIcast summ
BGP router identifier 2.2.2.2, local AS number 65001
BGP table version is 16, main routing table version 16
9 network entries using 1296 bytes of memory
15 path entries using 1140 bytes of memory
4/3 BGP path/bestpath attribute entries using 496 bytes of memory
1 BGP AS-PATH entries using 24 bytes of memory
0 BGP route-map cache entries using 0 bytes of memory
0 BGP filter-list cache entries using 0 bytes of memory
BGP using 2956 total bytes of memory
BGP activity 9/0 prefixes, 18/3 paths, scan interval 60 secs
Neighbor        V           AS MsgRcvd MsgSent   TblVer  InQ OutQ Up/Down  State/PfxRcd
2001:1:1::1     4        65001     289     285       16    0    0 04:10:09        7
2001:1:3::1     4        65001     328     326       16    0    0 04:45:34        7
R2#
R2#
###########Tabla BGP#########################

R2#SH BGp IPV6 UNIcast    
BGP table version is 16, local router ID is 2.2.2.2
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal,
              r RIB-failure, S Stale
Origin codes: i - IGP, e - EGP, ? - incomplete
   Network          Next Hop            Metric LocPrf Weight Path
*>i2001:1:1::/64    2001:1:1::1              0    100      0 i
*> 2001:1:2::/64    ::                       0         32768 i
*>i2001:1:3::/64    2001:1:3::1              0    100      0 i
* i2001:1:4::/64    2001:1:3::1              0    100      0 65002 i
*>i                 2001:1:1::1              0    100      0 65002 i
*>i2001:1:5::/64    2001:1:1::1              0    100      0 65002 i
* i                 2001:1:3::1              0    100      0 65002 i
* i2001:2:1::/64    2001:1:3::1            128    100      0 i
*>i                 2001:1:1::1              0    100      0 i
*>i2001:2:2::/64    2001:1:3::1              0    100      0 i
* i                 2001:1:1::1            128    100      0 i
* i2001:2:3::/64    2001:1:3::1              0    100      0 i
*>i                 2001:1:1::1              0    100      0 i
*>i2001:4:1::/64    2001:1:1::1              0    100      0 65002 i
* i                 2001:1:3::1              0    100      0 65002 i
############# Prueba de conectividad #######################
R2#ping 2001:1:5::1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2001:1:5::1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 28/31/36 ms
R2#

ipv6 ospf Frame-Relay

 

 

 

  

R1#sh ipv6 route
IPv6 Routing Table - 8 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
       U - Per-user Static route
       I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary
       O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
       ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
C   2001:1::/64 [0/0]
     via ::, Loopback0
L   2001:1::1/128 [0/0]
     via ::, Loopback0
O   2001:2::1/128 [110/64]
     via FE80::C201:1AFF:FE68:0, Serial1/0
O   2001:3::1/128 [110/64]
     via FE80::C202:1AFF:FE68:0, Serial1/0
C   2001:5::/64 [0/0]
     via ::, Serial1/0
L   2001:5::1/128 [0/0]
     via ::, Serial1/0
L   FE80::/10 [0/0]
     via ::, Null0
L   FF00::/8 [0/0]
     via ::, Null0
R1#

R1#sh frame-relay map
Serial1/0 (up): ipv6 FE80::C201:1AFF:FE68:0 dlci 102(0x66,0x1860), static,
              broadcast,
              CISCO, status defined, active
Serial1/0 (up): ipv6 2001:5::2 dlci 102(0x66,0x1860), static,
              CISCO, status defined, active
R1#
R1#sh frame-relay pvc
PVC Statistics for interface Serial1/0 (Frame Relay DTE)
              Active     Inactive      Deleted       Static
  Local          1            0            0            0
  Switched       0            0            0            0
  Unused         0            0            0            0
DLCI = 102, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial1/0
  input pkts 134           output pkts 123          in bytes 13708
  out bytes 12080          dropped pkts 0           in pkts dropped 0
  out pkts dropped 0                out bytes dropped 0
  in FECN pkts 0           in BECN pkts 0           out FECN pkts 0
  out BECN pkts 0          in DE pkts 0             out DE pkts 0
  out bcast pkts 6         out bcast bytes 480
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
  pvc create time 00:34:15, last time pvc status changed 00:08:39
R1#

CCNP ROUTE BGP 6-5 Case Study

  Configuracion de bgp:
 Local preference
 MED


R4#sh ip bgp
BGP table version is 21, local router ID is 172.16.12.1
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal,
              r RIB-failure, S Stale
Origin codes: i - IGP, e - EGP, ? - incomplete
   Network          Next Hop            Metric LocPrf Weight Path
*> 10.1.1.0/24      192.168.34.1                           0 65001 i
*                   192.168.14.1             7             0 65001 i
*  10.1.102.0/29    192.168.34.1       2681856             0 65001 i
*>                  192.168.14.1             7             0 65001 i
*> 10.1.103.0/29    192.168.34.1             0             0 65001 i
*                   192.168.14.1             7             0 65001 i
*> 10.1.203.0/29    192.168.34.1             0             0 65001 i
*                   192.168.14.1             7             0 65001 i
*> 10.2.2.0/24      192.168.14.1             7             0 65001 i
*                   192.168.34.1       2297856             0 65001 i
*> 10.3.3.0/24      192.168.14.1             7             0 65001 i
*                   192.168.34.1           350             0 65001 i
*> 10.20.0.0/24     192.168.14.1             7             0 65001 i
*                   192.168.34.1       2297856             0 65001 i
*> 10.20.0.0/16     192.168.34.1                           0 65001 i
*                   192.168.14.1             7             0 65001 i
*> 10.20.1.0/24     192.168.14.1             7             0 65001 i
   Network          Next Hop            Metric LocPrf Weight Path
*                   192.168.34.1       2297856             0 65001 i
*> 10.20.2.0/24     192.168.14.1             7             0 65001 i
*                   192.168.34.1       2297856             0 65001 i
*> 10.20.3.0/24     192.168.14.1             7             0 65001 i
*                   192.168.34.1       2297856             0 65001 i
s> 172.16.0.0/22    0.0.0.0                  0         32768 i
*> 172.16.0.0       0.0.0.0                            32768 i
s> 172.16.4.0/22    0.0.0.0                  0         32768 i
s> 172.16.8.0/22    0.0.0.0                  0         32768 i
s> 172.16.12.0/22   0.0.0.0                  0         32768 i
R4#

Challenge lab ccnp route 8-4

R1(config)

interface Serial1/0
 ip address 172.16.12.1 255.255.255.0
 serial restart-delay 0
end

router eigrp 1
 network 172.16.12.0 0.0.0.255

ipv6 router ospf 1
 router-id 1.1.1.1
 log-adjacency-changes
interface Loopback0
 no ip address
 ipv6 address FEC0::1:1/112
 ipv6 ospf 1 area 0

interface Tunnel1
 no ip address
 ipv6 address FCC0::13:1/112
 ipv6 ospf 1 area 0
 tunnel source 172.16.12.1
 tunnel mode ipv6ip
 tunnel destination 172.16.23.3




hostname R3
ipv6 unicast-routing
interface Tunnel1
 no ip address
 ipv6 address FCC0::13:3/112
 ipv6 ospf 1 area 0
 tunnel source 172.16.23.3
 tunnel mode ipv6ip
 tunnel destination 172.16.12.1
interface Serial1/1
 ip address 172.16.23.3 255.255.255.0
 serial restart-delay 0
interface Serial1/2
 no ip address
 ipv6 address FEC0:34::/64 eui-64
 ipv6 ospf 1 area 0
 serial restart-delay 0

router eigrp 1
 network 172.16.23.0 0.0.0.255
ipv6 router ospf 1
 router-id 3.3.3.3
 log-adjacency-changes

configuracon OSPF ios 15

R1#sh ver
Cisco IOS Software, 7200 Software (C7200-ADVSECURITYK9-M), Version 15.0(1)M9, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Wed 12-Sep-12 09:12 by prod_rel_team
ROM: ROMMON Emulation Microcode
R1 uptime is 12 minutes
If you require further assistance please contact us by sending email to
export@cisco.com.
Cisco 7206VXR (NPE400) processor (revision A) with 245760K/16384K bytes of memory.
Processor board ID 4279256517
R7000 CPU at 150MHz, Implementation 39, Rev 2.1, 256KB L2 Cache
6 slot VXR midplane, Version 2.1
2 FastEthernet interfaces
8 Serial interfaces
125K bytes of NVRAM.
65536K bytes of ATA PCMCIA card at slot 0 (Sector size 512 bytes).
8192K bytes of Flash internal SIMM (Sector size 256K).

Configuration register is 0x2102

R1(config)#ruter ospf 1
R1(config)#int s1/0
R1(config-if)#ip add 10.10.10.1 255.255.255.252
R1(config-if)#no shut
R1(config-if)#ip ospf 1 area 0
R1(config-if)#int f0/0
R1(config-if)#ip add 192.168.10.254 255.255.255.0
R1(config-if)#no shut
R1(config-if)#ip ospf 1 area 0

R2(config)#router ospf 1
R2(config)#int s1/0
R2(config-if)#ip add 10.10.10.2 255.255.255.252
R2(config-if)#no shut
R2(config-if)#ip ospf 1 area 0
R2(config-if)#int f0/0
R2(config-if)#ip add 192.168.20.254 255.255.255.0
R2(config-if)#no shut
R2(config-if)#ip ospf 1 area 0


R1# sh ip ospf nei
Neighbor ID     Pri   State           Dead Time   Address         Interface
192.168.20.254    0   FULL/  -        00:00:35    10.10.10.2      Serial1/0

R1#sh ip rou
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route, + - replicated route
Gateway of last resort is not set
      10.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
C        10.10.10.0/30 is directly connected, Serial1/0
L        10.10.10.1/32 is directly connected, Serial1/0
      192.168.10.0/24 is variably subnetted, 2 subnets, 2 masks
C        192.168.10.0/24 is directly connected, FastEthernet0/0
L        192.168.10.254/32 is directly connected, FastEthernet0/0
O     192.168.20.0/24 [110/65] via 10.10.10.2, 00:25:02, Serial1/0
R1#

ccna 5.0

 Ya falta poco para el lanzamiento de la neva curricula 5.0, segun lo anunciado los cambios que habran son:

-Integración de IPv6 e IPv4 en el diseño, configuración y administración de redes enrutadas y conmutadas. (ipv6 , protocolos de enrutamiento ripng eigrp for ipv6 ospfv3)

- Utilización de los comandos de Cisco IOS 15.x para configurar y administrar dispositivos de red. ( config de protocolos de enrutamiento por interface,...)

- Actualizaciones de los tópicos sobre tecnología avanzada que incluyen: Voz, inalámbrica, seguridad y centros de datos.( Qos,..)

- Mejora del análisis psicométrico de los elementos del examen final.
    
- Retroalimentación mejorada de las evaluaciones.

- Soporte a la movilidad para permitir acceso al texto y gráficos de los cursos desde plataformas móviles, incluyendo dispositivos con: IOS de Apple, Google Android y Windows 8.

-Plena Integración con Netspace para aprovechar al máximo la comunicación, y la colaboración entre los usuarios, estudiantes e instructores.

- Cisco estará realizando el lanzamiento por etapas del nuevo currículo, iniciando en Junio del 2013, y se espera que todos los cursos estén disponibles para el mes de Diciembre de 2013.

Se estarán enviando información actualizada sobre los avances y proximamente se enviara información con mayor profundidad en temas como:

Actualización de equipos de laboratorio.
Mantenimiento de software.
IOS 15 e IPV6.



Tab: Completes the remainder of the command or keyword
Ctrl+P (or up arrow): Displays the last command entered
Ctrl+N (or down arrow): Displays previous commands entered
Ctrl+A: Moves the cursor to the beginning of the current line
Ctrl+E: Moves the cursor to the end of the current line
Ctrl+F: Moves forward one character
Ctrl+B: Moves backwards one character

Esc+F: Moves forward one word
Esc+B: Moves backwards one word
Ctrl+R: Redisplays a line (starts a new line, with the same command shown)
Ctrl+U: Erases a line
Ctrl+W: Erases a word
Ctrl+Z: Exits configuration mode and returning you to privileged EXEC mode
Ctrl+Shift+6: Allow the user to interrupt an IOS process such as ping or traceroute
Ctrl+C: Aborts the current command and exits the configuration mod

Redistribucion OSPFv3 RIPng

R1(config )#
interface FastEthernet0/0
 ipv6 address 2001:1::1/64
interface FastEthernet0/1
 ipv6 address 2001:2::1/64
R1(config)#ipv6 router ospf 1
R1(config-rtr)#router-id 1.1.1.1
R1(config-rtr)#int f0/0
R1(config-if)#ipv6 ospf 1 area 0
R1(config-if)#int f0/1
R1(config-if)#ipv6 ospf 1 area 0

R1(config-if)#do sh ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route
Gateway of last resort is not set
R1(config-if)#do sh ipv6\ route
sh ipv6\ route
       ^
% Invalid input detected at '^' marker.
R1(config-if)#do sh ipv6 route
IPv6 Routing Table - 7 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
       U - Per-user Static route
       I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary
       O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
       ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
C   2001:1::/64 [0/0]
     via ::, FastEthernet0/0
L   2001:1::1/128 [0/0]
     via ::, FastEthernet0/0
C   2001:2::/64 [0/0]
     via ::, FastEthernet0/1
L   2001:2::1/128 [0/0]
     via ::, FastEthernet0/1
OE2  2001:3::/64 [110/50]
     via FE80::C205:CFF:FEEC:0, FastEthernet0/0
L   FE80::/10 [0/0]
     via ::, Null0
L   FF00::/8 [0/0]
     via ::, Null0



R2(config )#
interface FastEthernet0/0
 ipv6 address 2001:1::2/64
!
interface FastEthernet0/1
 ipv6 address 2001:3::1/64
!
#######Configuracion RIPng###############
R2(config)#ipv6 router rip ripng
R2(config-rtr)#redistribute ospf 1 metric 5 include-connected
R2(config)# int f0/1
R2(config-if)#ipv6 rip ripng enable

###########Configuracion OSPFv3###########
R2(config)#ipv6 router ospf 1
R2(config-rtr)#router-id 2.2.2.2
R2(config-rtr)#redistribute rip ripng include-connected metric 50
R2(config-rtr)#int f0/0
R2(config-if)#ipv6 ospf 1 area 0
R2(config-rtr)#    do sh ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route
Gateway of last resort is not set
R2(config-rtr)#    do sh ipv6 route
IPv6 Routing Table - 7 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
       U - Per-user Static route
       I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary
       O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
       ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
C   2001:1::/64 [0/0]
     via ::, FastEthernet0/0
L   2001:1::2/128 [0/0]
     via ::, FastEthernet0/0
O   2001:2::/64 [110/20]
     via FE80::C204:CFF:FEEC:0, FastEthernet0/0
C   2001:3::/64 [0/0]
     via ::, FastEthernet0/1
L   2001:3::1/128 [0/0]
     via ::, FastEthernet0/1
L   FE80::/10 [0/0]
     via ::, Null0
L   FF00::/8 [0/0]
     via ::, Null0
R2(config-rtr)#